USER MANUAL

COMING SOON

Minimum requirements

  • Android: 9.0 or later
  • iOS: 14.0 or later
  • Wi-Fi network generated by the DISMART 2.0 Gateway
  • Gateway and remote modules should be installed

 

Downloading and installing the mobile app

  1. Open the Google Play Store or the Apple App Store.
  2. Search for DISMART 2.0 and press Download. 

 

Physically installing the system

  1. Positioning the Gateway: Mount the gateway in a central location within the area that needs to be illuminated, ensuring it is away from heat sources and not enclosed in metal frames. This placement optimises radio transmission.
  2. Power connection: Connect the gateway to the power source and turn on.
  3. The lighting fixtures ordered with subcode -24 come with a pre-installed remote module.
  4. Lamps can be uploaded to the system even when they are turned off. This is done by scanning the QR code and following the instructions below.

Main menu for navigating between application sections

Button for creating programming groups or adding devices
Access to the details of a group's daily schedule

Detail of active programming

Access Active Daily Programming
Management of Lamp Groups and their programming
Management of associated devices
Manage the gateway configurations
Log out from the application

A coloured LED light on the gateway indicates its operating status. If the light is green, it means that the system is working correctly; if the light is red, it means that the gateway is in programming mode. If an operator forgets to exit a setup operation or a device/group details screen, the gateway will automatically return to operating mode after 5 minutes, changing the LED colour from red to green.

Selecting the language at startup

  1. Upon starting up the app, you will be prompted to choose your preferred language.
  2. Once you’ve selected a language, connect to a DISMART Gateway 2.0.

 

Connecting to the Gateway

  1. Make sure the DISMART 2.0 Gateway is powered on and installed.
  2. The default password to connect to the Gateway is: DisanoAdmin. You can change it later from the “Gateway” section of the main menu.
  3. On iOS: You need to manually enter the name of the Wi-Fi network generated by the gateway or scan the QR code on the device.
  4. Once connected to the gateway, you will be automatically logged into the system. At this point, you can start connecting lamps, create groups, add sensors and buttons, and programme the lighting management system.

Scanning remote modules

  1. Open the “Devices” main menu.
  2. Use the “+” button to add a device.
  3. Scan the QR Code on the module or enter the code on the label.
  4. Enter a name for the device, making sure it is at least 6 characters long and clearly identifies the type of device you’re connecting.
  5. If the device is connected to the power supply, make sure it is properly connected.

 

NOTE: We recommend registering all lighting fixtures, DALI-2 sensors, and buttons equipped with a remote board before connecting them to the power supply. If there are issues with a device’s connection status, disconnect the gateway from the power supply and restart it.

STATUS OF REGISTERED DEVICES:

1) Device not registered: This status means that the device is connected to the system but has not yet been recognised by the gateway. Make sure the device is powered. The gateway scans devices every minute to check their status. Wait at least one minute for the process to complete.

2) Not connected: This status means that the device is connected to the system, it has been recognised by the gateway, but it is not communicating with the gateway yet. Make sure the device is powered. The gateway scans devices every minute to check their status. Wait at least one minute for the process to complete.

3) Connected: The gateway is communicating with the device.

TESTING THE CONNECTED LIGHTING FIXTURES:

You can check that all connected lamps respond correctly to the system by adjusting their brightness using the light bulb button. This brightness setting is temporary and for testing purposes only. It will revert to normal once you exit the test screen.

Adding Device

Button for testing connected lamps
Screen for manually adding a device
Button to scan the QR code for connection
Functionality screen for testing lamps connected to the gateway

Creating a Group

  1. Go to the Group Management section of the main menu.
  2. Click the “+” button to create a new group.
  3. Enter a name for the group, making sure it is at least 5 characters long and include a mandatory description.
  4. Press “Create group” to register the new group with the gateway. Adding a new group may take up to 10 seconds. Do not exit the app while the group is being saved.
List of groups entered into the system

Button to create a device group

Adding Device

Each group must have a name and a mandatory description of at least 5 characters
  1. Go to the Group Management section of the main menu.
  2. Select the Group to which the devices will be added by opening its management page and clicking the > icon.
  3. Use the button at the bottom right corner of the screen to connect one or more devices.
  4.  Click on the link icon to view the list of devices that are not yet connected to a group and select the ones you wish to connect.
  5. Press the “Add to Group”  button to complete the operation.

Note: When creating and setting up a group, the gateway enters programming mode, interrupting normal system operation. Once you’ve finished setting up the group, you must return to the list of groups. If you forget to do this, the system will automatically resume normal operation 5 minutes after you exit the app. 

Group management sheet
Button to access the list of devices connected to the group

Click icon to connect new devices to the group

Click this icon to perform a brightness test on all the lighting devices connected to the group
Button to add the selected devices to the group
    1. Go to the “Groups” menu.
    2. Select the group for which you wish to schedule the days of the week.
    3. Select the day of the week and use the pencil button to start scheduling the time slots.
    4. Click on “Add time slot”, set a start and end time and the brightness rate.
    5. If you wish to add other time slots, press the “Add time slot” again. A new time slot will be suggested with a start time after the last time slot entered.
    6. Once you’ve finished entering the time slots, use the “Save” button to save the schedule on the gateway.
    7. Repeat these steps for the days of the week you wish to schedule.
     

    NOTES and WARNINGS:

    1. Unscheduled time slots or days of the week: For the time slots and days that have not been scheduled yet, the system will turn on all lamps at 100% brightness. We recommend setting up at least one time slot (from 00:00 to 24:00) for each day, with the brightness set to 0%, if you want to keep the lighting system off. 
    2. You can set up to 10 time slots per day.
    3. When setting the time slots, the gateway enters programming mode, interrupting normal system operation until you exit the group management page.
Copy and Paste Function of Single Day Time Slot Programming
Management of the insertion and modification of time slots.
Viewing configured time slots
Button to add a time slot
Management panel for the start and end of programming of a time slot and lighting value
Button for saving scheduled time slots
  1. Go to the “Groups” menu.
  2. Select the group for which you wish to schedule the exception.
  3. Click the “+” button in the “Exceptions” section.
  4. Fill in the required information, specifying the Name of the event, the calendar date and decide whether this exception should be repeated every year.
  5. Click on “Add time slot”, set a start and end time and the brightness rate.
  6. If you wish to add other time slots, press the “Add time slot” again. A new time slot will be suggested with a start time after the last time slot entered.
  7. Once you’ve finished entering the time slots, use the “Save” button to save the schedule on the gateway.

NOTES and WARNINGS:

  1. Unscheduled time slots or days of the week: For the time slots and days that have not been scheduled yet, the system will turn on all lamps at 100% brightness. We recommend setting up at least one time slot (from 00:00 to 24:00) for each day, with the brightness set to 0%, if you want to keep the lighting system off.
  2. You can set up to 10 time slots per day.
  3. When setting the time slots, the gateway enters programming mode, interrupting normal system operation until you exit the group management page.
Inserting a specific calendar day with dedicated programming.
Button to add a time slot
Saving the exception in the gateway

Management of the Normally‑Open Push Button Connected to a Group

  1. Enter the “Groups” menu.
  2. Select the group that contains the push button you want to manage.
  3. Scroll down to the “General Button” section.
  4. Configure the operating mode of the button by choosing between Timeoutand Push to dimm:
    • Timeout — when the button is pressed, the light turns on at the configured brightness level. Once the set time (in minutes) expires, the light automatically returns to the level defined by the group’s programming.
    • Push to dimm — with a short press, the light turns on at the configured value or returns to the level defined by the group’s programming. With a long press, the brightness can be adjusted between 5% and the maximum configured value. The brightness level set through dimming is stored and reused at the next activation.
  5. Click the “Save” button in the section to apply the button’s operating mode.


Notes and Warnings

  • In Timeout mode, you must set a duration between 1 minute and 180 minutes. When the configured time ends, the light automatically returns to the level defined by the normal programming of the associated group.
  • In Push to dimm mode, short presses manage switching on and returning to the programmed level, while long presses allow brightness adjustment between 5% and the maximum configured value. The dimmed level is stored for the next activation.
  • While configuring a group’s button, the gateway enters programming mode, temporarily interrupting normal system operation until you exit the group management page.

Button to save the physical button settings

Time in minutes to timeout after pressing the button. Must have a value between 1 and 180 minutes

Go to the main menu and select Gateway to open the related management and setting options.

From this menu you can manage:

  1. The gateway clock and send the time, date, and time zone from the smartphone connected via the app.
  2. Back up or restore the saved settings.
  3. Change the gateway password.
  4. View the firmware version of the gateway board.


Note: Opening the Gateway menu will put the system into programming mode, interrupting normal operation until you exit this section.

Access to the gateway card management system
Access the system to set a date and time on the gateway or transfer information from the connected smartphone
Access to the creation functions Backup the configuration or restore a saved configuration
Changing the gateway login password
Gateway Firmware Version Information

In the “Gateway” section of the main menu, you can export the configuration settings to your smartphone and restore them later. On Android devices, the backup file is automatically saved in the documents folder. On iOS devices, you will be prompted to choose a location to save the file. The backup file looks something like this: dismart2-YYMMDD-HHMMSS.db. To restore the configuration settings, you will need to find the backup file on your device. 

From the main menu, select “Devices” to view the list of devices connected to the system and open the lamp management page.

This screen displays:

  1. Name and code of the connected lamp, with the option to edit both.
  2. A “Find device” feature to make the lamp flash. The lamp will turn off automatically after 20 seconds. Once you exit the management screen, the lamp will revert to the programming status set by its group within 1 minute.
  3. A test button, which allows you to test the lamp’s dimming functionality.
  4.  Area for managing the connection of a lamp to a group.
  5. Area displaying the current status of the remote board.


Note: Opening the details page of a lamp will put the system into programming mode, interrupting normal operation until you exit this section.

Access to the gateway card management system
Access to the details and management of a lamp or other device

Changing the lamp name


Button that makes the lamp flash to identify it.

Button to perform dimming tests on the single lamp

Area for connecting or disconnecting from a device group

From the main menu, select “Devices” to view the list of devices connected to the system and open the sensor management page.

This screen displays:

  1. Name and code of the connected sensor, with the option to edit both.
  2. A button which enables to set the light sensor to up to 5 preset options.
  3. Area displaying the current status of the sensor.
  4. Service Tools, including the “Rescan” function to force a search for the sensor in the system.
  5. A “Device in OTA mode” (Dispositivo in modalità OTA) function to enable firmware updates for the sensor (this operation can only be performed by Disano technicians).

 

Adjusting the sensor:

The light sensor must be adjusted in the absence of natural light, using a certified lux meter.

Using the calibration management blocks, you can enter a LUX value detected by the certified lux meter, corresponding to the dimming value of the lamps connected to the group. The values recorded in the presets can then serve as a reference for defining the brightness expected during a given time slot.

Replacing the DALI-2 sensor connected to the board:

If you need to replace the sensor connected to the remote board of the DISMART 2.0 system, you can force the new sensor to align with the system by pressing “Scan DALI line again”.

Note: Opening the details page of a lamp will put the system into programming mode, interrupting normal operation until you exit this section.

Access to the device management system
 
 
Changing the sensor name and serial number
Opening area for entering sensor calibration values
Button for connecting or dissociating the sensor from a group
Management block of the calibration values ​​of a sensor. There are up to 5 configurable presets
Button to send the dimming value to the lamps in the group based on the preset being recorded
Button to save the set preset.
Button to allow firmware updates to specialized and authorized technicians

Button to force the gateway to search for the DALI2 device in case of failure to detect the device or replacement of the sensor connected to the remote module.

The gateway clock can be managed via the Gateway Management Menu, under the Gateway Time section.

From here, you can:

  • Send the date, time, and time zone directly from your smartphone to the gateway.
  • View the time currently set on the gateway.

 

Daylight Saving Time

The gateway automatically updates its internal clock based on international daylight saving time rules provided by the IANA (Internet Assigned Numbers Authority).

This ensures accurate time synchronisation without the need for manual adjustments during seasonal changes.

If a light sensor has been added to a group, setting the time slot allows you to use the “Constant Light” function, which is based on a preset from the light sensor. This preset can be selected from the “Lux Set” drop-down menu in the time slot management screen. 

If the sensor is a motion sensor, you can also adjust the timeout (minimum 1 minute), which determines the percentage of light dimming when no movement is detected.

Select one of the presets connected to the Dali2 brightness sensor

Percentage of group dimming in the absence of movement

Standby timeout of the last motion detection by the sensor

Save settings button

Secondary PIR Timeout (HOLD TIME)

With version 1.1.0 of the application, a secondary PIR timeout level has been introduced. This optional timeout activates after the first inactivity period detected by the motion sensor. When the PIR sensor no longer detects presence, at the end of the first timeout the system does not immediately switch off the lights. Instead, it applies a progressive dimming down to the configured value, maintaining reduced illumination for the duration defined in the secondary timeout. Only when this second timeout expires are the lights fully switched off. This feature can be configured individually for each time slot and allows for a more natural and comfortable management of environments, avoiding abrupt switch‑offs in cases of slow or infrequent movement.

Management of Devices with System‑Wide Override

Global Devices are devices that act on the entire system, overriding the programming configured for individual groups. Through this function, it is possible to manage simple buttons and DALI keypads with up to 4 channels, ensuring manual control of lighting independently from programmed scenarios.

How to Activate a Global Device

To display a device within the Global Devices menu, access the Devices menu, select the desired device, and assign it to the Global Group. Only after this operation will the device be visible and manageable from this section.

You can connect one or more DALI keypads to the system, with up to 4 independent channels. Each button on the keypad can be configured individually by choosing between two operating modes:

  • Scene association: each button can be linked to a specific scene, recalling it when pressed.
  • Override via Global Group: the button acts as an override on the entire system. The options Enable Dimmer and Enable Button Timeout also apply in this context, with the same behaviour described for single buttons.

 

Features Introduced with the Application Update

  • Bluetooth power management: it is now possible to adjust the system’s Bluetooth signal strength by choosing between high‑power and low‑power modes. The change is applied simultaneously to the Gateway and propagated as a notification to all connected remote nodes, optimising coverage and consumption based on the installation environment.
  • Gateway reboot: a dedicated button is now available to reboot the Gateway directly from the application, without requiring physical interaction with the hardware.
  • Configuration backup and restore: you can perform a full backup of the Gateway programming — including scenes, groups, and devices — and restore it when needed, ensuring operational continuity even in case of device replacement or reset.